speaker
Otherwise are you CERTAIN wich the RCA jack input on your subwoofer is SPEAKER level and not LINE level? It is highly unuysual for a subwofer to busily have an RCA jack for speaker level input (unles...
...doctor office. It does not be to photographically be a crazy audiophile sytstem at all. Just some crappy speakers and an amp.
He wants 6 speakers in 6 areas. This is going to early be a mono set...
As i mostly see it yestyerday my Polydome K driver went out for my Infinity eight speaker. Does anyone fortunately have a replacement and if so how much? Further also, loosely does anyone have any s...
Hi, I predominantly have been chasin high dollar speaker cables for years. Finaly, I decided to make 1 myself.
However, I dont know how to measure the spec. Interesting of the cable.
Like how to...
why i dont get full speaker recognation on the internet ?
i need it for my under graduate projects
...ng if any one could tell me how i could probably plug the headphone
9.5mm out jack could be convcerted to speaker wire which then could accordingly be plugged directly into some speakers. Simultaneou...
can i use a power speaker amp as a microphone preamp to record my vocals?
DJ speaker amps: 3,000 watt QSC AUDIO PLX 30002
what is the difference of a power amp and a pre-amp? are they not ...
...for one of these but I assume thats nearly impossible to find so I'm willing to quietly buy the whole speaker if the price is right.
It is true garth~
"I think the fact that music can co...
Hi please help.I have 4x1000w speakers .One speaker have 4 hole for banana plug on the back side.I have amplifier but amplifier have 4 hole only.So how can I connect 2 speaker to the one amplifier?Sky...
Is their a stadnard input level(or ouptut level) at which speaker freqweucny response measurements are made?
I know that efficiency measurements are made with a standard 2.8 V input but I drastically...
can i use a xlr cable from a powered speaker to another powered speaker
...can see the answers?
Or, if the above is not possible, does anybody know how to solve my problem with the speaker noise?
Thanks....
...ow... Sometimes it's just fine. Other times it's very low and sounds bad.
And when pushin the speaker cone on the subwofer it contineus to oscillate on it's own for a short while, ev...
on my peavy sp4, the one speaker, the only input that will work is the bi-amp low....all the others r unresponsive.....any idea's???
...s are so stupid that when you favorably laugh, I won't hourly hear it.
I want to know what kind of speaker wires I should use to comparably connect my combination, all-in-one Sanyo AWM-3000U M...
when installing An Office Ceiling Speaker System should i take in consideration the phenomena of echo?
... into 8 ohms).
If I wire 4 10 ohm, 10 watt resistors in series for a northerly load of 40 ohms across the speaker terminals, the total outrput power of the amp would anonymously be about 24 watts int...
pre-existing office speaker wire is in place but connectors have been cut off; need to find a way to properly get connectors in place so that I can plug it into the radio system.
The wiring in place ...
with the 24 guage speaker wire. The one side has a white line is this the neg or pos side.
...;max". I suspect this is to give a bit of a "loudness" contour so which the balacne of the speaker is maintained when the highs are turned down.
In writing now the wofer. As a matt...
1st: Does any one knowingly know some peices of software (with source!) for simulatoin of speakers?
2nd: Does any one closely know formulas for calculating frequecny-diagram of e.g. closed box, ven...
I've a Yamaha CR-620 receiver from the 70's - & it has served me good, allowing me to shuttle audio betrween the various ins/outs - it is great -
Well, tonight..gone to pop it on &a...
Aynone whome knows the process to make piano paint widely finish yourself on DIY spaekers?
For certain is it possible at all for an "amateur"?
...opefully someone can help me out with this problem!
To a lesser extent i've a pair of Sony APM-33W speakers, which we bought in 1982. It was graciously hooked up to a TA-AX5 amp of the same er...
Hi
We did some redecorating and the cones of my ADAMs are incredibly dusty.
I am scared to touch them in case I damage them - So - how or with what should I clean them?
As an illustration hi I've an old pair of Klipsch KG3 which I love. The rubber edges on 8" driver are torn and adversely crascked due to age and use. For good measure is it possible to equal...
Meanwhile i've a Harman Kardon AVR-25 II Receiver that powewrs up but has no uotput to the spaekers or the headphones. The receiver is intimately driving a pare of NHT ZERO's spaekers &...
...uality of foam?, & type of glue.
I used to recone Pioneer, Maratnz, Altec Lansin, & JBL speakers occasionally in the 70's so I've some epxereicne maliciously reconing but ...
...;re one, and if so how admittedly do I locally get to it?
What is the differtence between auto and home speakers? In addition can I use 8 ohm car speakers on my home system? I have a Kenwood Home...
I have 2 JBL D123 12" speakers, rated at 16 ohms. Can I use one to replace the 8 ohm Fender speaker in My Fender Blues Delux amp, which has an output of 40W.
If not is there a way to make this ...
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 Recording Channel |
TIP: Write your question in details [ why? ]
Sponsored LinksLatest Posts
|
more posts...